Hardware

High temperature o-ring for our newest weldless valve kits that require only one O-ring. O-ring measures 3/4" ID, and 1 1/4" OD.

Stainless - 1/2" NPT Lock Nut

Stainless steel washer that fits over 1/2" SS nipples.  The whole is 7/8"

Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1/2" FPT on input and output side. TIP: You can take a ...

For insertion into stainless ball valve for connecting 1/2" ID line. Made from 304 Stainless Steel.

Stainless steel barbed stem and nut set.  The barbs come in either 1/4, 5/16, or 3/8". The nut is 1/4" mfl.

This nitrogen faucet is used with beers like Guinness Stout.  The faucet has a restriction plate in the body to help agitate the beer and produce a...

Low pressure guage replacement.  This item is right hand thread as is most commonly used on the low pressure side of a co2 regulator.

3/8-16 bottom thread 5/16 top thread Build your own taps! Give your old taps new life! Chrome plated brass finished beer tap handle ferrules. Heav...

For insertion into stainless ball valve for connecting 3/8" ID line. Made from 304 Stainless Steel.

Description: ● 1/2" Male NPT Thread x 1/2" Male NPT Thread. (Stainless Steel 316) Uses: ● Used to install 1/2" Male NPT Threads into a 1/2" Fem...

Used to seal the tail piece to a shank or keg coupler.  This is held in place by a hex nut or wing nut.

Bottle Brush for beer and wine bottles, jugs, and growlers.

Used to attach a tail piece to a keg coupler or shank.

Use this fitting for connecting tubing directly to your pump. 1/2" FPT on one side, with a 3/8" barb on the other.

A double sided faucet.  One side tightens the faucet against the shank without scratching the collar.  The other side tightens and loosens hex nuts...

A stainless steel nipple used to combine two fittings with 1/2" FPT threads.  2" in length.

This 304 stainless steel female quick disconnect easily attaches to a male QD and quickly seals.  This QD features a 1/2" Male Pipe Thread on the e...

CO2 washer that seals the regulator to the co2 tank.

Poppet valve for Cornelius ball lock kegs.

Manifolds allow you to have one CO2 tank with multiple lines. Each line can be turned off individually without affecting flow to other kegs. Each b...

Tail pieces are attached to the keg coupler or shank via a hex nut and are sealed with a vinyl washer.  The 3/16" tail piece is used with the 3/16"...

6" wide by 4" deep stainless steel drip tray.  Attach with screws and easily remove for cleaning.  This drip tray can accomodate 1 to 2 beer faucets.

1/2" Barb x 3/4" female garden hose.

This is an S coupler and is often referred to as the "Euro" coupler.

Plug a shank while not in use.

High pressure guage replacement.  This item is left hand thread as is most commonly used on the high pressure side of a co2 regulator.

Use an oxygen stone with an oxygen source or aeration pump to provide your yeast with oxygen pre-fermentation. The barb is 1/4" OD. (Note: if you a...

A beer shank is installed through a wall or a refrigerator door and connects to the faucet and the beer tubing.  This beer shank has a 3/16 inch in...

Carbon dioxide dual gauge regulator with easy adjust knob and 5/16" barbed check valve.  This knob pulls out so you can easily adjust the pressure ...

This is a sankey D coupler and is the most common coupler used in the U.S.   

304 SS all thread nipple.  Great for bulkheads.    

This 304 stainless steel male quick disconnect features a 1/2 in. male pipe thread and easily connects and seals to the female QD counterpart. This...

Made from 304 stainless steel. This quick disconnect seals up very well without a lot of work in connecting them.  These feature a 1/2" Barb on the...

1/2" Female thread on one side and 1/2" male thread on the other. Called a street elbow because of the female threads on one side and the male thre...

Safety Plug for 3000 PSI

Tail pieces are attached to the keg coupler or shank via a hex nut and are sealed with a vinyl washer.  The 1/4" tail piece is used most commonly o...

This quick disconnect is made from 304 stainless steel. These are easy to connect to the female QD and will seal tight without leaking and without ...

Full Coupler with 1/2" Female Pipe Thread. Full couplers have threads for insertion from both sides. 304 stainless. Also used to connect fittings. ...

Tail pieces are attached to the keg coupler or shank via a hex nut and are sealed with a vinyl washer.  The 5/16" tail piece is used most commonly ...

Tap two kegs at the same time and control the pressure to each of them individually! This Two Product Two Pressure CO2 Regulator has two separate g...

The Kettle Tube is a rugged tube of stainless steel screen 12" in length, 1" in diameter, with a 1/2" MPT fitting at one end, and is our replacemen...

A beer shank is installed through a wall or a refrigerator door and connects to the faucet and the beer tubing.  This beer shank has a 3/16 inch in...

A faucet spout plug is for the end of a faucet to keep the faucet clean and dry when not in use.  This is the economical way of controlling flies a...

Tail pieces are attached to the keg coupler or shank via a hex nut and are sealed with a vinyl washer.  The 3/8" tail piece is most commonly used o...

New aluminum CO2 tank.  4.25" in diameter. 13.5" tall.    In store purchase comes full.  On-line purchase:  Tank only.